Updates to an existing Momentum EA

MQL4 Experten

Auftrag beendet

Ausführungszeit 11 Tage

Spezifikation

Required updates:

1) The EA is currently only opening buy trades, but should open both buy and sell (indicator buffers are working correctly therefore a relatively minor update)

2) The 'max trades’ setting currently counts the total buy and sell trades, however I would like it to count:

   - Max trades - combined total, as per current setting
   - Max buy trades – maximum buy trades allowed
   - Max sell trades – maximum sell trades allowed

3) New setting so the EA doesn't close trades if the floating value of the open trade is $negative, added thus:

   - Do not close ANY trades if open trade value is $negative - True/False
   - Do not close a partial close setting if open trade value is $negative - True/False
   
4) A further setting that closes X lots after X pips. The setting must work alongside the other partial close settings so both can work at the same time.

5) This setting applies to the first trade only when the EA is attached to the chart - don’t trade till the next opposite signal:

   - If the previous signal was a buy, wait until the next sell signal to open first trade - True/False
   - First trade only

6) Do not open a trade if the last candle closed was in the opposite direction:

   - if a SELL signal appears directly after a BULLISH candle, do not trade (vice versa for a BUY) - True/False

7) Max no of consecutive candles before a signal:

   - if more than X BULLISH candles appear before a BUY signal do not trade (vice versa for a SELL) - 1x integer, if ‘0’ do not use

8) Pause after candle close before opening a trade:

   - a setting to pause X ms after the candle has closed before opening the trade – 1x integer
   - this is to avoid the occasional event when the indicator repaints after candle close

9) Wait for a two candle reversal before opening a new trade - True/False

   - If set to True, a BUY trade can only open if there is a sequence of two or more bearish candles between the previous BUY trade closing and the current BUY signal (vice versa for a SELL).  This setting only applies to trades in the same direction that closed IN PROFIT, therefore should not affect an opposite signal.

Bewerbungen

1
Entwickler 1
Bewertung
(378)
Projekte
401
31%
Schlichtung
63
19% / 70%
Frist nicht eingehalten
51
13%
Beschäftigt
2
Entwickler 2
Bewertung
(3)
Projekte
5
0%
Schlichtung
2
0% / 100%
Frist nicht eingehalten
2
40%
Arbeitet
3
Entwickler 3
Bewertung
(87)
Projekte
114
26%
Schlichtung
7
29% / 57%
Frist nicht eingehalten
5
4%
Frei
Ähnliche Aufträge
I'm looking for an MQL5 expert to develop a trading EA that uses the ratio of candle wicks to body sizes to automatically enter and exit trades. Key features should include: - Autopilot function: The EA should handle trade entries without manual intervention. Trade exits are only by hitting trailing SL. - Trade criteria: Trades should only be placed based on specific, pre-defined ratios of candle wicks to body sizes
EA BREAKOUT SNR 30 - 100 USD
I need a developer who can work with quickly & details. Create EA MT5 with features :: 1. Can identify Support and Resistance (based on close candle) 2. Marking SNR Breakout Zone 3. There is a multitimeframe breakout scanner & History Setup Dashboard Panel 4. Scan the valid setup that appears (Compare 2 Timeframes) 5. There is manual marking of zone(box), SPREAD INFO & Next Bar Time, EXPIRED DATE & LOCK ACC 6
Double PSAR 30+ USD
Some code isn't so good. Coders should code. I want solid code, not copied, not from EA Builder or similar tool. Please see written requirements and rules below. Please see picture attached. I hope these are clear. GBPUSD, H1, September 12-20, 2024 How closely can your coding match the picture? Indicators: PSAR Step: .01 Maximum: .01 Advanced PSAR Start AF: .02 Step: .02 Max AF: .2 MACD Colored Fast: 50 Slow: 100
Convert my tradingview pine script to mt4, Its a simple and straight code i need an expert programmer to convert my tradingview pine script to mt4, Thats All Thank you
The 1HSM EA allows users to configure trade settings, including activation, trading session, trade timing, maximum simultaneous trades, and stop loss type (virtual or visible). Users can set breakeven parameters, slippage control, and profit trailing options (gap, block, or target). Reverse trading can be enabled, allowing trades in the opposite direction if the price reverses significantly. Specific conditions for
Hello, i would like to have a fix on my plotted lines I use a liquidity strategy on the 1 hr time frame but the indicator that i am using for plotting the 1 hr lines is having a issue and printing the plot lines all over the place on the current 1 and 4 hr plot line as you can see in the screenshot this is very disturbing while i am trading can u fix that or just remove the current 1 hr plot line ?and or only show
"Hello, I am new to MT5 and ALGO TRADING. I am seeking a skilled and experienced trader to professionally manage and optimize my MT5 account together with me. I am using QUANTUM EMPEROR MR5 and Gallileo FX with 6 Premium Settings and seek help to get started and make this profitable. I will also share my profits with you. Please reach out to discuss potential collaboration."
Hi good day, Am looking for a professional programer who can help me ,I need a strategy built. Can you help , please reach out and send some necessary details that you need from me
I want to convert a tradingview indicator into an mt5 ea. The name of the indicator is trend trader strategy. So after converting the strategy for the EA is a reverse martingale. And I want the following options. Can you make the following optional and choices I can make. Max daily profit, max daily lost, ema, tp like pips or percentage gain, the multiplier, and the step between each trade
I have an EA that I want to have some additional work done to, including a logical stop loss system, and adding some extra conditions to the entry criteria. This is quite a complex EA, so the programmer will need to be experienced in MQL5 coding

Projektdetails

Budget
30+ USD
Für die Entwickler
27 USD
Ausführungsfristen
von 1 bis 2 Tag(e)