OrderSend error: 4111,4110

New comment
 

When I set “Long Only” or “Short Only” in the advisor settings, the terminal sees error 4110 or 4111, how can I write a check for position allowing in the code before completing the OrderSend function.

Here is my code.

double spread = Ask-Bid;
   int total = OrdersTotal();
   if(total == 0 && OrderBarAllow())
     {
      if(CheckCandle()==1) 
        {
         ticket = OrderSend(Symbol(),OP_BUY,Lot,Ask,slippage,0,Ask + TakeProfit*Point+spread,"APE V4.0",Magic);
         if(ticket<0)
           {
            Print("OrderSend Error #",GetLastError());
           }
         else
            Print(" OrderSend ended succesfully",ticket);

        }
      if(CheckCandle()==0)
        {
         ticket = OrderSend(Symbol(),OP_SELL,Lot,Bid,slippage,0,Bid - TakeProfit*Point-spread,"APE V4.0",Magic);
         if(ticket<0)
           {
            Print("OrderSend Error #",GetLastError());
           }
         else
            Print("OrderSend ended sucessfully",ticket);

        }
     }
 
Write your own input for select if long, short or both and adjust your code according to input value.

You will be also ready to switch to MT5 that do not have the option like MT4 and the only way is using an input.
 

  1. Why did you post your MT4 question in the MT5 General section instead of the MQL4 section, (bottom of the Root page)?
              General rules and best pratices of the Forum. - General - MQL5 programming forum? (2017)
    Next time, post in the correct place. The moderators will likely move this thread there soon.

  2. Per #1

  3.          ticket = OrderSend(Symbol(),OP_BUY,Lot,Ask,slippage,0,Ask + TakeProfit*Point+spread,"APE V4.0",Magic);

    You buy at the Ask and sell at the Bid. Pending Buy Stop orders become market orders when hit by the Ask.

    1. Your buy order's TP/SL (or Sell Stop's/Sell Limit's entry) are triggered when the Bid / OrderClosePrice reaches it. Using Ask±n, makes your SL shorter and your TP longer, by the spread. Don't you want the specified amount used in either direction?

    2. Your sell order's TP/SL (or Buy Stop's/Buy Limit's entry) will be triggered when the Ask / OrderClosePrice reaches it. To trigger close at a specific Bid price, add the average spread.
                MODE_SPREAD (Paul) - MQL4 programming forum - Page 3 #25

    3. The charts show Bid prices only. Turn on the Ask line to see how big the spread is (Tools → Options (control+O) → charts → Show ask line.)

      Most brokers with variable spreads widen considerably at end of day (5 PM ET) ± 30 minutes.
      My GBPJPY shows average spread = 26 points, average maximum spread = 134.
      My EURCHF shows average spread = 18 points, average maximum spread = 106.
      (your broker will be similar).
                Is it reasonable to have such a huge spreads (20 PIP spreads) in EURCHF? - General - MQL5 programming forum (2022)

  4. Why did you post your MT4 question in the MT5 General section instead of the MQL4 section, (bottom of the Root page)?
              General rules and best pratices of the Forum. - General - MQL5 programming forum? (2017)
    Next time, post in the correct place. The moderators will likely move this thread there soon.

  5. Risk depends on your initial stop loss, lot size, and the value of the symbol. It does not depend on margin or leverage. No SL means you have infinite risk (on leveraged symbols). Never risk more than a small percentage of your trading funds, certainly less than 2% per trade, 6% account total.

    1. You place the stop where it needs to be — where the reason for the trade is no longer valid. E.g. trading a support bounce, the stop goes below the support. Then you compute your lot size.

    2. AccountBalance * percent/100 = RISK = OrderLots * (|OrderOpenPrice - OrderStopLoss| * DeltaPerLot + CommissionPerLot) (Note OOP-OSL includes the spread, and DeltaPerLot is usually around $10/PIP, but it takes account of the exchange rates of the pair vs. your account currency.)

    3. Do NOT use TickValue by itself - DeltaPerLot and verify that MODE_TICKVALUE is returning a value in your deposit currency, as promised by the documentation, or whether it is returning a value in the instrument's base currency.
                MODE_TICKVALUE is not reliable on non-fx instruments with many brokers - MQL4 programming forum (2017)
                Is there an universal solution for Tick value? - Currency Pairs - General - MQL5 programming forum (2018)
                Lot value calculation off by a factor of 100 - MQL5 programming forum (2019)

    4. You must normalize lots properly and check against min and max.

    5. You must also check Free Margin to avoid stop out

    6. For MT5, see 'Money Fixed Risk' - MQL5 Code Base (2017)

    Most pairs are worth about $10 per PIP. A $5 risk with a (very small) 5 PIP SL is $5/$10/5 or 0.1 Lots maximum.

 
Fabio Cavalloni #:
Write your own input for select if long, short or both and adjust your code according to input value.

You will be also ready to switch to MT5 that do not have the option like MT4 and the only way is using an inpТ

Thank you.

 
William Roeder #:

  1. Why did you post your MT4 question in the MT5 General section instead of the MQL4 section, (bottom of the Root page)?
              General rules and best pratices of the Forum. - General - MQL5 programming forum? (2017)
    Next time, post in the correct place. The moderators will likely move this thread there soon.

  2. Per #1

  3. You buy at the Ask and sell at the Bid. Pending Buy Stop orders become market orders when hit by the Ask.

    1. Your buy order's TP/SL (or Sell Stop's/Sell Limit's entry) are triggered when the Bid / OrderClosePrice reaches it. Using Ask±n, makes your SL shorter and your TP longer, by the spread. Don't you want the specified amount used in either direction?

    2. Your sell order's TP/SL (or Buy Stop's/Buy Limit's entry) will be triggered when the Ask / OrderClosePrice reaches it. To trigger close at a specific Bid price, add the average spread.
                MODE_SPREAD (Paul) - MQL4 programming forum - Page 3 #25

    3. The charts show Bid prices only. Turn on the Ask line to see how big the spread is (Tools → Options (control+O) → charts → Show ask line.)

      Most brokers with variable spreads widen considerably at end of day (5 PM ET) ± 30 minutes.
      My GBPJPY shows average spread = 26 points, average maximum spread = 134.
      My EURCHF shows average spread = 18 points, average maximum spread = 106.
      (your broker will be similar).
                Is it reasonable to have such a huge spreads (20 PIP spreads) in EURCHF? - General - MQL5 programming forum (2022)

  4. Why did you post your MT4 question in the MT5 General section instead of the MQL4 section, (bottom of the Root page)?
              General rules and best pratices of the Forum. - General - MQL5 programming forum? (2017)
    Next time, post in the correct place. The moderators will likely move this thread there soon.

  5. Risk depends on your initial stop loss, lot size, and the value of the symbol. It does not depend on margin or leverage. No SL means you have infinite risk (on leveraged symbols). Never risk more than a small percentage of your trading funds, certainly less than 2% per trade, 6% account total.

    1. You place the stop where it needs to be — where the reason for the trade is no longer valid. E.g. trading a support bounce, the stop goes below the support. Then you compute your lot size.

    2. AccountBalance * percent/100 = RISK = OrderLots * (|OrderOpenPrice - OrderStopLoss| * DeltaPerLot + CommissionPerLot) (Note OOP-OSL includes the spread, and DeltaPerLot is usually around $10/PIP, but it takes account of the exchange rates of the pair vs. your account currency.)

    3. Do NOT use TickValue by itself - DeltaPerLot and verify that MODE_TICKVALUE is returning a value in your deposit currency, as promised by the documentation, or whether it is returning a value in the instrument's base currency.
                MODE_TICKVALUE is not reliable on non-fx instruments with many brokers - MQL4 programming forum (2017)
                Is there an universal solution for Tick value? - Currency Pairs - General - MQL5 programming forum (2018)
                Lot value calculation off by a factor of 100 - MQL5 programming forum (2019)

    4. You must normalize lots properly and check against min and max.

    5. You must also check Free Margin to avoid stop out

    6. For MT5, see 'Money Fixed Risk' - MQL5 Code Base (2017)

    Most pairs are worth about $10 per PIP. A $5 risk with a (very small) 5 PIP SL is $5/$10/5 or 0.1 Lots maximum.

Thank you.

New comment