LSMA, Polynomial and other Regression with Experts and Indicators - page 10

 

And here is new graph of the indicator in 2008 this time there is no filter adding with the indicator for positioning orders .

buy condition = signal green point below the line + slope direction lime color

this is the result of the indicator alone still not optimized and im only trying it on EURUSD for now.

avi1:
is it indi ? its emty,? or its ea

THIS is an indicator and that graph is the behavior of the indicator in 2008 its just to have some idea .

Files:
slsma.jpg  81 kb
 

mtfslsma v1

Baba_master:
And here is new graph of the indicator in 2008 this time there is no filter adding with the indicator for positioning orders .

buy condition = signal green point below the line + slope direction lime color

this is the result of the indicator alone still not optimized and im only trying it on EURUSD for now.

THIS is an indicator and that graph is the behavior of the indicator in 2008 its just to have some idea .

i try afew times to put on chart and nada empty whats wrong

 
avi1:
i try afew times to put on chart and nada empty whats wrong

nothing wrong, something on your side (hate .ex files)

Files:
lsma_slsma.gif  10 kb
 

last post in this tread

hi

This is my final result for now for here

Time frame = h4

Currency = eurusd

Smooth_ratio = 0.5

Rperiod = 46

Buy = slope green + signal point green below the line

Sell = vice versa

Stoploss & takeprofit = 0

Trailing stop = (daily average range) / 3

Exit = when no or opposite signal

with this setup you would get this result in 2008 till now (below) , in average 1 trade a week .

c u around

Files:
last.jpg  102 kb
 
 
pray1956:
I have downloaded LMSA Anytime Frame EA v1.1 from forexproject.com. This has your name on it as well as appearing identical to LMSA Daily EA v1.1.mq4 on this site on the first thread. I have also downloaded the indicator LSMA in Color 3B. The indicator works very well. However, the EA which I assumed works based on this indicator does not conform to the indicator. When the indicator stays the same color say red. The Ea closed the short trade well before any signal by the indicator. This has happened on several occasions. So far the indicator has been correct in its signals, however, the EA has been wrong. This has happened on several occasions both in entering and exiting the trades. I would like the EA to perform exactly as the indicator. Can you or someone help me? Ray

Ray,

Sorry for the long delay in answering. I have ben very busy.

The EA uses the cross of two lsma lines. One that I use for the daily is the 7/16 cross.

That is why the single indicator does not match the trades.

Robert aka MrPip

 

Template?

MrPip:
Ray,

Sorry for the long delay in answering. I have ben very busy.

The EA uses the cross of two lsma lines. One that I use for the daily is the 7/16 cross.

That is why the single indicator does not match the trades.

Robert aka MrPip

Robert,

do you have a template you could share?

 

Hello Robert,

Many thanks for sharing the items in this thread with everyone. Are you using the ones only on the first post or in other posts?

Regards,

Jeff

MrPip:
Ray,

Sorry for the long delay in answering. I have ben very busy.

The EA uses the cross of two lsma lines. One that I use for the daily is the 7/16 cross.

That is why the single indicator does not match the trades.

Robert aka MrPip
 
Baba_master:
hi friends

here im sharing one of my indis (SLSMA) lets see if its useful

the result below shows the behavior of the indicator (settings not optimized) in 2008 with (smoothed ma 55 Chanel) as a filter (very quick ea).

try out different settings and compare it with LSMA,

khaste nabashid.

This has to be one of the Best and most over looked indy's here on TSD

 

LSMA Direction

Hi Robert,

I tried to run Lsma_v1[1][1].0.mq4 as LSMA Direction EA.

I have few question:

1) Is it the correct one ?

2)If I set useDelay=0 it enter trades continuosly not when the LSMA indicator color change. Is it normal?

3) If I use LSMA in Color as indicator , I wrote the following code to recognize when LSMA color change :

bool difference_found=false;

double LSMA_index0,LSMA_index1,LSMA_index2;

LSMA_index0=iCustom(NULL,0,"LSMA in Color",34,1500,0,0);

LSMA_index1=iCustom(NULL,0,"LSMA in Color",34,1500,1,0);

LSMA_index2=iCustom(NULL,0,"LSMA in Color",34,1500,2,0);

if(LSMA_index0 != LSMA_index1 || LSMA_index1!=LSMA_index2 || LSMA_index0!=LSMA_index2)

{

difference_found=true;

}

string sComment;

sComment="";

sComment=sComment+"LSMA color0=" +LSMA_index0+"\n";

sComment=sComment+"LSMA color1=" +LSMA_index1+"\n";

sComment=sComment+"LSMA color2=" +LSMA_index2+"\n";

sComment=sComment+"Difference found=" +difference_found+"\n";

Comment(sComment);

but it never set difference_found = true ;-(

The value of LSMA_index0, LSMA_index1, LSMA_index2 are always the same

Can you help me?

4) my intention is to write an LSMA Direction EA that enter the trade on changing LSMA color from red/yellow to green -> buy and exit the trade when the opposite color change happen

Thanks in advance for you valid support

Fabio